AKR 890 Whirlpool

Petunjuk AKR 890 Whirlpool

(1)
  • 5019 318 33199
    EXTRACTOR OR FILTERING HOOD INSTALLATION
    The minimum distance between the cooker support surface and the lowest part of the hood must not be less than
    40 cm, for gas and 30 cm for electric cookers (65 cm from controls as per enclosed drawing) If the installation
    instructions for the gas cooker specify a greater distance, this must be taken into account. The fume hose and
    hose clamps are not supplied. We recommend that you contact a qualified engineer to have the hood installed.
    Also consult the drawings on the first pages of this booklet, with alphabetical references in the description.
    Always comply with the instructions and recommendations given in this manual. The Manufacturer declines all liability for any
    faults, damage or fires caused by the appliance as a result of failure to observe the instructions and recommendations given in
    this manual.
    If the hood is used in FILTER version it is used without an exhaust fume discharge pipe.
    Fumes and vapour are recycled through the deflector F (11F).
    If the product is to be used in EXTRACTOR version, it is necessary to provide an exhaust pipe from the top outlet B to the
    external outlet vent.
    In this case a collar (11A) must be fitted on the exhaust outlet B and the carbon filter must be removed.
    A telescopic flue is also available (as an accessory).
    Preliminary information for installing the hood:
    Expansion plugs are provided to secure the hood to most types of ceilings. However, a qualified technician is needed to make
    sure that the plugs are suitable for your ceiling. The ceiling must be strong enough to take the weight of the hood.
    Only for some models
    An aesthetic flue can be purchased as an optional accessory. Please check with your After-sales Service to find out whether or
    not your model. has this option.
    In order to ensure that it is installed in the most suitable way, it is recommended that you only fit the hood after purchasing the
    flue.
    Disconnect the power supply at the domestic main switch before carrying out electrical connections.
    Apply the (adhesive) rubber strips C to the back of the hood.
    If necessary (if the wall is not perfectly vertical or if it is partially tiled) fit two spacers D in correspondance with the final
    fixing holes (snap-fitting).
    Trace a centre line on the wall to facilitate installation (1), position the drilling template on it so that the central line printed
    on the template matches the central line marked on the wall and the bottom part of the template is aligned with the
    bottom of the hood when mounted (2).
    Drill two holes (Ø 8 mm) and fix the support bracket to the wall using two wall plugs and screws (3).
    Remove the steam deflector and take out the grease filter (see relevant paragraph).
    Hang the hood (4), adjust its position (5-6) and from the inside of the hood mark two points for final fastening (7), remove
    the hood and drill two holes (Ø 8 mm) (8), insert two wall plugs, hang the hood again and fasten it to the wall with two
    screws (9).
    Carry out the electrical connection (10), but leave the hood disconnectedfrom the main power supply.
    If the hood is to be used in the extractor version, fit the collar supplied on the hood outlet (11A - extractor version - also
    install an exhaust pipe of suitable diameter) in place of the deflector (11F - filter version).
    Fit the grease filter, fit and close the steam deflector.
    Warning!
    If the hood is to be used in the extractor version, remove the carbon filter if there is one, along with the fixing
    elements (behind the grease filter - see relevant paragraph).
    If the hood is to be used in filter version, check that the carbon filter has already been fitted at the back of the grease filter,
    and if this is not the case, purchase a carbon filter and fit it.
    Connect the hood to the main power supply.
    GB
    Gas cooker
    Electric cooker
    D F NL E
    GB
    P IGR
    31833199.fm Page 5 Monday, March 13, 2006 12:00 PM
AKR 890 Whirlpool

Apakah Anda memiliki pertanyaan tentang AKR 890 Whirlpool?

Jumlah pertanyaan: 0

Ajukan pertanyaan anda mengenai Whirlpool AKR 890 di sini kepada pemilik produk lainnya. Sampaikan dekripsi yang jelas dan singkat tentang masalah dan pertanyaan anda. Semakin jelas penjelasan masalahnya, semakin mudah bagi pemilik Whirlpool AKR 890 lainnya untuk menyediakan jawaban terbaik.

Tampilkan panduan gratisWhirlpool AKR 890 di sini. Anda sudah membaca panduan tetapi tidak menjawab pertanyaan anda? Silakan ajukan pertanyaan anda pada halaman ini kepada pemilik Whirlpool AKR 890 lainnya. Ajukan pertanyaan Anda di sini

spesifikasi produk

Umum
Brand Whirlpool
Model AKR 890
Produk Tudung pembuangan asap
EAN 8003437775178
Bahasa Inggris
Jenis berkas PDF
Daya
Tenaga motor 170W
Performa
Jumlah kecepatan 3
Jenis ekstraksi Disalurkan/Disalurkan kembali
Kecepatan intensif
Daya ekstraksi maksimal 630m³/j
Tingkat kebisingan 46dB
Desain
Tipe kontrol Tombol
Sejumlah bohlam 4
Tipe bohlam Halogen
Daya bohlam 20W
Warna produk Baja Antikarat
Tipe Tipe dinding
Penyaringan
Jumlah filter 1buah
Jenis pelumas filter Logam
Berat dan dimensi
Panjang 800mm
Lebar 435mm
Tinggi 757mm
Berat 28100g
Fitur lainnya
Persyaratan daya 220 - 230 V, 50 Hz, 16 A

petunjuk.co.id

Mencari panduan? petunjuk.co.id menjamin anda untuk menemukan panduan yang anda cari dalam waktu singkat. Database kami memuat lebih dari 1 juta panduan PDF untuk lebih dari 10,000 merek. Setiap hari kami menambahkan panduan terbaru sehingga anda akan selalu menemukan produk yang anda cari. Sangat mudah: hanya dengan mengetikkan nama merek dan tipe produk dalam kotak penelusuran dan anda akan melihat secara instan panduan yang anda pilih secara online dengan gratis.

petunjuk.co.id

© Hak Cipta 2020 petunjuk.co.id. Hak Cipta Dilindungi.