Petunjuk RTH230B Honeywell

RTH230B Honeywell
9.2 · 2
PDF petunjuk
 · 4 halaman
Inggris
petunjukHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Tampilkan panduan gratis Honeywell RTH230B di sini. Anda sudah membaca panduan tetapi tidak menjawab pertanyaan anda? Silakan ajukan pertanyaan anda pada halaman ini kepada pemilik Honeywell RTH230B lainnya. Ajukan pertanyaan Anda di sini

Apakah Anda memiliki pertanyaan tentang RTH230B Honeywell?

Apakah Anda memiliki pertanyaan tentang Honeywell dan apakah jawabannya tidak ada di manual?

  • Terima pembaruan tentang solusi
  • Dapatkan jawaban atas pertanyaan Anda

Tanya Jawab

Jumlah pertanyaan: 0

Honeywell RTH230B adalah termostat digital untuk mengontrol suhu pada sistem pemanas atau pendingin dalam rumah. Termostat ini dilengkapi dengan layar LCD yang mudah dibaca dan intuitif, serta kontrol tombol yang mudah digunakan untuk mengatur suhu sesuai keinginan pengguna. Termostat ini juga memiliki fitur pengatur waktu, yang memungkinkan pengguna untuk mengatur suhu secara otomatis pada waktu tertentu sesuai dengan jadwal harian mereka. Honeywell RTH230B sangat mudah untuk dipasang dan dirancang untuk cocok dengan sebagian besar sistem pemanas atau pendingin yang umum digunakan di rumah. Termostat ini juga dilengkapi dengan perlindungan memori baterai untuk menghindari kehilangan pengaturan saat terjadi pemadaman listrik. Termostat Honeywell RTH230B tidak hanya membantu menghemat energi dan biaya, tetapi juga mengurangi dampak kemungkinan perubahan suhu pada kesehatan dan kenyamanan pengguna. Produk termostat ini memiliki harga yang terjangkau dan layak untuk dipertimbangkan sebagai alternatif termostat konvensional.

Umum
BrandHoneywell
ModelRTH230B
Produktermostat
BahasaInggris
Jenis berkasPanduan pengguna (PDF)

Tidak dapat menemukan jawaban atas pertanyaan Anda di manual? Anda dapat menemukan jawaban atas pertanyaan Anda di FAQ tentang Honeywell RTH230B di bawah ini.

Di mana lokasi terbaik untuk menempatkan termostat?

Tempat terbaik untuk termostat adalah ruangan tempat Anda menghabiskan sebagian besar waktu, dalam banyak kasus ruang tamu atau dapur. Tempatkan termostat sekitar satu setengah meter di atas lantai, jangan di bawah sinar matahari, dan jangan di dinding luar.

Apa itu zona mati di termostat?

Jika termostat Anda memiliki zona mati, instalasi Anda sebagaimana adanya disebut sebagai 'tidak bergerak'. Termostat hanya menyala ketika, misalnya, terjadi perbedaan yang menyimpang lebih dari 2˚C dari suhu ruangan yang disetel.

Berapa suhu ruangan yang ideal?

Kebanyakan orang menemukan bahwa suhu ruangan yang ideal adalah antara 19 dan 22 derajat Celsius.

Apakah buku panduan untuk Honeywell RTH230B tersedia dalam bahasa Bahasa Indonesia?

Sayangnya, kami tidak memiliki buku panduan untuk Honeywell RTH230B dalam bahasa Bahasa Indonesia. Buku panduan ini tersedia dalam bahasa Inggris.

Apakah pertanyaan Anda tidak terdaftar? Ajukan pertanyaan Anda di sini

Tidak ada hasil