W220VW Creda

Petunjuk W220VW Creda

(1)
  • INSTRUCTIONS on INSTALLATION & USE for W200FW and W220VW
    Creda recommends, for your own safety and to ensure you get the best possible results from your Washing
    Machine, you read through this booklet and follow these steps thoroughly.
    Choose a location for your washing
    machine where possible on a solid floor,
    with the electrical sockets and water
    supply taps easily accessible.
    Allow sufficient space: 600mm width,
    600m depth and 900mm height.
    DO NOT install in a bath or shower
    room.
    Dispose of packaging material in a safe
    place and remove any labels.
    Please read through thoroughly to
    ensure you understand each stage
    before you begin.
    Read the rest of these instructions to get the best from your appliance, remember to fill in your guarantee registration.
    Keep this Book in a safe place for quick reference.
    STEP 1 STEP 2
    A wash chart is provided to help you to
    select your required programme.
    Examples given for the maximum
    washing load weight for different fabric
    types.
    STEP 4
    WARNING: This appliance must be earthed.
    Remember you will be charged for a service call if a
    problem with your washing machine is caused by
    incorrect installation or misuse.
    Electrical Guide Installation Guide
    Programme Selector Dial
    Read through this section to familiarise
    yourself with the different
    compartments within the dispenser
    drawer.
    STEP 3
    Dispenser Drawer
    NOTE: Always follow manufacturer’s dosage
    recommendations.
    All available optional wash features are
    explained within this section - These
    allow you to adjust your selected wash
    programme to suit your needs.
    STEP 6
    Options Guide
    How to start your selected programme
    and how to stop or change the
    programme if so required.
    STEP 5
    Using your Machine
    NOTE: Progress indicator lights show what stage in
    the programme cycle has been reached.
    We recommend the Persil range of
    detergent products.
    STEP 8
    Troubleshooting
    A picture guide provides a clear
    explanation how to set a wash
    programme.
    DO NOT overload the washing machine.
    STEP 7
    A Typical Wash Programme
    NOTE: Creda recommend, on completion of your
    programme, that you switch off both the
    electricity and water supply to the appliance.
    Please refer to the Troubleshooting
    section if you have any problems when
    using your washing machine.
    There may be nothing wrong!
    NOTE: In addition to the temperature of the
    incoming water, the selection of optional wash
    features will affect the programme times.
    READ BEFORE
    CONTACTING
    SERVICE!
    Merloni Elettrodomestici UK Ltd, Morley Way, Peterborough, PE2 9JB.
    PRINTED BY SIMLEX
    .
    FOUR ASHES,WOLVERHAMPTON. 09/2004 - 195046949.00
    Creda guarantee
    After Sales Service
    “Satisfaction guaranteed or your money back”
    We give you a unique ‘satisfaction guaranteed’ promise - valid
    for 90 days - after you have purchased your Creda appliance.
    If there is a technical problem simply call Creda Repair service
    or visit our web-site at www.theservicecentre.co.uk and where
    necessary, we will arrange for an engineer to call.
    If the technical problem is not resolved under this guarantee,
    we will replace your machine or, if you prefer, give you
    your money back.
    All Creda appliances carry a fully inclusive 12 month parts and
    labour guarantee.
    Guarantee terms and conditions
    Your guarantee is only applicable in the United
    Kingdom or Republic of Ireland and is subject to the
    following provisions that your appliance:
    Has been installed and used correctly in accordance with
    this instruction booklet.
    Has been used solely for domestic purposes and is located
    on domestic premises (ie. not for commercial or trade
    use).
    Has been properly connected to a suitable electrical
    supply voltage as stated on the appliance rating plate.
    Has not been subject to misuse, accident, modified or
    repaired by anyone other than one of our own service
    engineers.
    For pre purchase information on any other Creda
    product,
    call: 08701 54 64 74 or visit: www
    .creda.co.uk
    Recycling & Disposal
    Information
    As part of Creda’s continued commitment to helping the environment,
    we reserve the right to use quality recycled components to keep down
    customer costs and minimise material wastage.
    Please dispose of packaging and old appliances carefully.
    To minimise risk of injury to children, remove the door, plug and cut
    mains cable off flush with the appliance. Dispose of these parts
    separately to ensure that the appliance can no longer be plugged into
    a mains socket, and the door cannot be locked shut.
    “No company is better positioned to offer an after sales service on
    a Creda appliance than us - the manufacturer”.
    As part of our commitment to you, all Creda appliances have the added
    benefit of a fully inclusive parts and labour guarantee for the first 12
    months. All in-guarantee repairs are guaranteed for the remainder of your
    original guarantee period.
    When the 12 months parts and labour guarantee expires we offer the
    following after sales service options:
    Repair Service and Information Help Desk
    UK: 08709 066066
    www
    .theservicecentre.co.uk
    Republic of Ireland: 1850 302 200
    Note: Our operators will require the Model number and the Serial number
    of your appliance.
    Available 364 days a year with a fast, effective and value for money
    service.We have the largest white goods repair service in the UK with over
    1200 of our own fully trained engineers.
    All chargeable repairs include a parts and labour guarantee for 12
    months from the date of the repair.
    If you require any information or have any questions about your
    appliance, our operators are on hand with help and advice.
    All this ensures that you will receive the best available after sales service
    possible.
    Extended Warranties
    UK: 08709 088 088
    www.theservicecentre.co.uk
    Republic of Ireland: 1850 502 200
    Whether you have just one or a number of Creda appliances in your
    kitchen, we offer two service cover plans to give you total peace of mind.
    Repair Protection Plan - FREE service repairs for a single Creda
    appliance during the period of cover.
    Kitchen Cover - FREE service repairs for all your Creda
    appliances less than 8 years old.
    Genuine Parts and Accessories
    UK: 08709 077 077
    www
    .theservicecentre.co.uk
    Republic of Ireland: (01) 842 6836
    A wide range of genuine parts and accessories are available from our
    hotline or through our web site.
    Genuine parts and accessories, extended warranties and service
    repairs are all available on our web-site at:
    www.theser
    vicecentre.co.uk
    Getting to Know your Appliance
    Plumbing Indicator Line label
    Hot Water inlet point and
    supplied Hose (Red or Grey end)
    Cold Water inlet point and
    supplied Hose (Blue end)
    Transit Bolts (both MUST be removed
    before using your machine).
    Control Panel
    Interlocking door
    and release lever
    Rating Plate
    Mains Cable
    Drainage Hose
    Hooked End Support
    Dispenser Drawer
    Model W220VW shows the maximum features available
    Adjustable Feet
    Wheels
    Key Contacts
    After Sales Service
    Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in both the appliances and
    services we offer.
    Extended Warranties
    UK: 08709 088 088
    (Open 8 to 8 Mon - Sun)
    www.theservicecentre.co.uk
    Republic of Ireland: 1850 502 200
    Genuine Parts and Accessories
    UK: 08709 077 077
    (Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)
    www
    .theservicecentre.co.uk
    Republic of Ireland: (01) 842 6836
    Cleaning the Exterior:
    Use a damp cloth or silicon polish to clean the exterior surfaces of the
    appliance.
    Cleaning the Door Bowl:
    Clean the internal surface of the door bowl regularly with a soft cloth.
    A build up of soap powder and water hardness residue may result in
    water leaking from the door.
    Repair Service and Information Desk
    UK: 08709 066 066
    (Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)
    www.theservicecentre.co.uk
    Republic of Ireland: 1850 302 200
    Note: Our operators will require the following information:
    The Model number (which can be found on
    the control panel)
    The Serial number (which can be found on the
    inner door trim)
    Cleaning the Dispenser Drawer & Compartments:
    It is advisable to clean the dispenser drawer regularly:
    1
    Pull the drawer out until it reaches its stop.
    2
    Press the drawer release latch
    down to remove the dispenser
    drawer.
    4
    Relocate the dispenser drawer and push it
    firmly back into place.
    3
    A
    B
    Clean and dry the
    dispenser drawer,
    syphons, grate and
    fabric conditioner exit
    channel (A).
    Also,regularly clean the
    outlet pipe area (B).
    Do not try to clean any
    part of the dispenser
    drawer while the machine
    is working.
    WARNINGS:
    Do not clean any part of the
    machine with abrasive cleaners,
    scouring agents, acids, any
    bleaches or metal polish, as
    they may cause damage.
    3
    CONNECT TO THE WATER
    SUPPLY...
    The Dispenser Drawer
    STEP 3
    Electricity Supply Installation
    WARNING:
    The appliance must be earthed.
    CE marking certifies that this appliance conforms to the following
    EEC directives:
    Low Voltage Equipment - 72/23/EEC & 93/68/EEC
    Electromagnetic Compatibility - 89/336/EEC, 92/31/EEC & 93/68/EEC
    Fuses
    Your appliance comes fitted with a plug and a 13 amp (13A) fuse.If
    you need to replace the fuse, use only those rated at 13 amp (13A)
    and ASTA approved to BS1362.To change the fuse lift the holder to
    vertical position and lift the fuse out. To replace the fuse, insert the
    fuse and push fuse holder down into the locked position. Correct
    replacement is identified by colour coding or the marking on base of
    plug.
    WARNING: Do not use the plug unless the fuse holder is in the locked
    position and the top cover firmly replaced.
    Changing the Mains Lead
    If you have damaged the existing lead and need a new one, contact
    Creda Service UK on: 08709 066 066 or www.theservicecentre.co.uk
    (or in the Republic of Ireland on: 1850 302 200). A charge will be
    made.We strongly advised that fitting a new lead is carried out by a
    qualified electrician.
    Seek professional advice if you need to use an extension lead.
    Changing the Plug
    If you need to change your plug, if it does not fit your socket: isolate
    the machine from the mains supply. Cut off the supplied plug and
    safely dispose of the discarded plug. DO NOT plug into any other
    socket.
    NOTE: If you change the plug, the colour of wires in the mains lead
    may not match the colour of the markings which show the different
    terminals in the plug.You must wire it as shown below:
    Green and yellow (Earth)
    wire to terminal marked ‘E’,
    symbol , or coloured
    green and yellow.
    Blue (Neutral) wire to
    terminal marked ‘N’ or
    coloured black.
    13A ASTA approved fuse to
    BS1362.
    Brown (Live) wire to terminal
    marked ‘L or coloured red.
    Adding Fabric Conditioner
    Dispensing Powder Detergent
    Dispensing Liquid Detergent
    ii
    i
    Index:
    1. Drawer release latch
    2. Pre-wash detergent compartment
    Maximum 200ml powder or
    100ml liquid
    3. Main detergent compartment
    Maximum 400ml powder or
    200ml liquid
    4. Grate
    5. Fabric conditioner compartment
    120ml maximum
    1
    2
    3
    4
    5
    To achieve the best wash results the
    manufacturers recommended amount
    of detergent should be measured and
    added to the main detergent
    compartment (II symbol) (max. 400ml).
    Alternatively you can obtain a liquid
    detergent flap, a barrier for the dispenser
    drawer.
    Contact Genuine Parts and Accessories
    (see Key Contacts)
    Pour the recommended
    amount of fabric
    conditioner into the
    compartment
    (flower symbol).
    Do not exceed the
    maximum fill line.
    Pre-wash Programme A
    When selecting programme A,
    add detergent to both the
    pre-wash compartment (I symbol)
    and the main wash compartment
    (II symbol).
    DO NOT use in drum dosing
    devices with the Pre-wash
    programme, A.
    4
    DRAINAGE SYSTEM... we recommend one of the following:
    1
    POLYSTYRENE BLOCK...
    5
    LEVEL?...
    NOTE: ALTHOUGH YOU MAY NEED TO
    MOVE THE HOOKED END SUPPORT
    ALONG THE GREY DRAINAGE HOSE,
    DO NO
    T REMOVE IT.
    WHICHEVER DRAINAGE METHOD
    YOU USE, MAKE SURE THAT THE
    HOOKED END SUPPORT IS FIXED
    LEVEL TO, OR ABOVE THE ‘PLUMBING
    INDICATOR LINE’*
    (*see Getting to Know your Appliance)
    This is part of the packaging and
    should have come away with the
    polystyrene base.
    IF IT HAS NOT... REMOVE IT!
    NOTE: YOU MAY NEED A SECOND
    PERSON TO HELP YOU RAISE AND
    LOWER THE APPLIANCE.
    PLEASE USE THE NEW HOSES SUPPLIED, FITTED
    TO THE MACHINE.
    If you have no hot water supply...
    Old hoses may
    cause leaks due to
    worn out washers.
    YOUR MACHINE WILL BE NOISY IF THE TWO FRONT FEET ARE NOT
    ADJUSTED SO THE MACHINE STANDS FIRM AND LEVEL.
    Check both hot
    and cold water
    supplies are
    running freely...
    A cold fill adaptor is available from
    your local authorised Service
    Centre or by calling the Genuine
    Parts & Accessories Hotline (see
    Key Contacts).
    Connect fill hoses to
    water supply taps:
    Red or Grey Hose end
    to Hot and Blue Hose
    end to Cold.
    TURN BOTH TAPS ON...
    Turn one or both front feet
    clockwise until the machine
    stands firm and level.
    The spring on each foot will
    stop them coming loose.
    2
    REMOVE TWO TRANSIT FIXINGS... Follow these instructions to remove the TWO transit fixings.
    IMPORTANT:
    Situated, one either
    side of the rear panel,
    both transit bolts
    (complete with
    spacers) MUST be
    removed before use...
    Failure to do so may
    cause damage to
    your machine!
    DO NOT REMOVE!
    STANDPIPE METHOD
    UNDER SINK METHOD
    OR
    Attach the GREY
    drainage hose to the
    under sink drainage
    unit securely, using a
    hose clip.
    Fix the hooked
    end support at
    a minimum
    800mm from
    the floor.
    cut off the blocked
    end of the under sink
    drainage unit.
    7
    READY...
    TO CHECK ALL PARTS OF THE INSTALLATION AND TO THOROUGHLY
    CLEAN THE INSIDE OF YOUR MACHINE:
    RUN PROGRAMME ‘B’ (refer to ‘Programme Selector Dial’, STEP 4).
    6
    CONNECT TO THE POWER SUPPLY...
    PLUG YOUR MACHINE INTO AN ELECTRICAL SOCKET WHICH IS
    EASILY ACCESSIBLE. SWITCH ON
    NOTE: We recommend extension
    leads are not used.
    Move your machine into position,
    take care not to trap or kink the
    hoses.
    WITHOUT ANY LAUNDRY
    WITHOUT ANY DETERGENT
    and
    THIS WILL TAKE APPROXIMATELY 2hours TO COMPLETE
    .............................
    Standpipe height:
    minimum 500mm
    from the floor.
    Insert drainage hose
    approximately 100mm
    into the standpipe.
    It is important the transit
    bolt and spacer come out
    intact (see pic).
    For safety, replace both
    plastic covers over the
    holes left by removing
    the two bolts.
    Use a crosshead
    screwdriver to
    remove the
    plastic cover.
    Unscrew the
    bolt using a
    13mm spanner.
    ST
    OP when 3
    threads can be
    seen.
    Hold, slide
    across and pull
    to remove.
    800mm
    from floor
    Hooked End Support
    STEP 1 STEP 2
    WARNING:
    Do not put any items into
    the drawer, other than
    detergents designed to be
    released from the drawer, as
    they may cause damage or
    blockage.
    We recommend the use of a detergent dosing ball,as provided by your detergent
    manufacturer.
W220VW Creda

Apakah Anda memiliki pertanyaan tentang W220VW Creda?

Jumlah pertanyaan: 0

Ajukan pertanyaan anda mengenai Creda W220VW di sini kepada pemilik produk lainnya. Sampaikan dekripsi yang jelas dan singkat tentang masalah dan pertanyaan anda. Semakin jelas penjelasan masalahnya, semakin mudah bagi pemilik Creda W220VW lainnya untuk menyediakan jawaban terbaik.

Tampilkan panduan gratisCreda W220VW di sini. Anda sudah membaca panduan tetapi tidak menjawab pertanyaan anda? Silakan ajukan pertanyaan anda pada halaman ini kepada pemilik Creda W220VW lainnya. Ajukan pertanyaan Anda di sini

spesifikasi produk

Umum
Brand Creda
Model W220VW
Produk Mesin Cuci
Bahasa Inggris
Jenis berkas PDF

petunjuk.co.id

Mencari panduan? petunjuk.co.id menjamin anda untuk menemukan panduan yang anda cari dalam waktu singkat. Database kami memuat lebih dari 1 juta panduan PDF untuk lebih dari 10,000 merek. Setiap hari kami menambahkan panduan terbaru sehingga anda akan selalu menemukan produk yang anda cari. Sangat mudah: hanya dengan mengetikkan nama merek dan tipe produk dalam kotak penelusuran dan anda akan melihat secara instan panduan yang anda pilih secara online dengan gratis.

petunjuk.co.id

© Hak Cipta 2020 petunjuk.co.id. Hak Cipta Dilindungi.