SLM221 Chief

Petunjuk SLM221 Chief

(1)
  • INSTALLATION INSTRUCTIONS
    Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
    no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
    of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
    implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
    Chief Manufacturing, a products division of Milestone AV Technologies
    8401 Eagle Creek Parkway, Savage, MN 55378
    • P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
    8802-000284 Rev01
    ©2009 Milestone AV Technologies,
    a Duchossois Group Company
    05/09
    SSB-221, SSM-221, SLB-221 and SLM-221 Interface Brackets
    SSB-221, SSM-221, SLB-221 and SLM-221 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
    installation instructions provided with the mount for additional installation information.
    Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
    WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
    DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
    Installation Instructions
    WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
    DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
    NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
    1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
    2. Turn projector upside down on a flat surface.
    3. Place nylon spacers onto the bottom of the projector and align spacers with the threaded inserts in the projector.
    4. Place the interface bracket onto the bottom of the projector and nylon spacers and align the holes in the bracket with the threaded inserts
    in the bottom of the projector.
    5. Position the M4 x 25mm mounting screws into the mounting holes. Tighten all fasteners at this time, securing the bracket to the projector.
    NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation instructions in the
    All-Points Security Kit.
    Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
    (1) Interface Bracket (5) Spacer, Nylon, .50 x .257 x .625
    (4) 10-24 Thumb Nuts ** (5) Screw, Phillips flat head, M4 x 25mm
    (1) All-Points Security Kit (1) Key, 5/32"
    **Only used when installing SLB/SSB interface brackets.
    NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
    encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
    interface bracket installation.
    SLB-221
    SLM-221
    (Note
    : SSB-
    style
    interfa
    ce bra
    c
    k
    e
    t
    c
    o
    n
    n
    e
    t
    i
    o
    n
    s
    a
    r
    e
    e
    n
    c
    i
    r
    c
    l
    e
    d
    )
    (
    N
    o
    t
    e
    :
    S
    S
    M
    -
    s
    t
    y
    l
    e
    i
    n
    t
    e
    r
    f
    a
    c
    e
    b
    r
    a
    c
    k
    e
    t
    c
    o
    n
    n
    e
    c
    t
    i
    o
    n
    s
    a
    r
    e
    e
    n
    c
    i
    r
    c
    l
    e
    d
    )
    Towards front of
    projector
    Towards front of
    projector
SLM221 Chief

Apakah Anda memiliki pertanyaan tentang SLM221 Chief?

Jumlah pertanyaan: 0

Ajukan pertanyaan anda mengenai Chief SLM221 di sini kepada pemilik produk lainnya. Sampaikan dekripsi yang jelas dan singkat tentang masalah dan pertanyaan anda. Semakin jelas penjelasan masalahnya, semakin mudah bagi pemilik Chief SLM221 lainnya untuk menyediakan jawaban terbaik.

Tampilkan panduan gratisChief SLM221 di sini. Anda sudah membaca panduan tetapi tidak menjawab pertanyaan anda? Silakan ajukan pertanyaan anda pada halaman ini kepada pemilik Chief SLM221 lainnya. Ajukan pertanyaan Anda di sini

spesifikasi produk

Umum
Brand Chief
Model SLM221
Produk Penyangga panel datar
EAN 841872114231
Bahasa Inggris
Jenis berkas PDF
Performa
Jenis dudukan -
Berat maksimal (kapasitas) -kg
Produk yang kompatibel BrightLink 425Wi\r
BrightLink 430i\r
BrightLink 430W\r
BrightLink 435W\r
BrightLink 435Wi\r
EB-410W\r
PowerLite 400\r
PowerLite 410W\r
PowerLite 420\r
PowerLite 425W\r
PowerLite 430\r
PowerLite 435W

petunjuk.co.id

Mencari panduan? petunjuk.co.id menjamin anda untuk menemukan panduan yang anda cari dalam waktu singkat. Database kami memuat lebih dari 1 juta panduan PDF untuk lebih dari 10,000 merek. Setiap hari kami menambahkan panduan terbaru sehingga anda akan selalu menemukan produk yang anda cari. Sangat mudah: hanya dengan mengetikkan nama merek dan tipe produk dalam kotak penelusuran dan anda akan melihat secara instan panduan yang anda pilih secara online dengan gratis.

petunjuk.co.id

© Hak Cipta 2020 petunjuk.co.id. Hak Cipta Dilindungi.