Petunjuk L-PB Atdec

L-PB Atdec
9.1 · 1
PDF petunjuk
 · 2 halaman
Inggris
petunjukAtdec L-PB

Step 2. Fasten Base to Work Surface - Choose DESK CLAMP OR BOLT THROUGH option (PTO...)

Component Checklist

A - DESK CLAMP

The default base setup allows 360° of

rotation of the Lower Arm around the base.

If you want to limit the Lower Arm rotation to

180° go to A1, if not skip to A2.

A1. OPTIONAL 180° ROTATION

To limit the Lower Arm rotation to 180° insert

the Brake Pin underneath the Desk Clamp.

Brake

Pin (x1)

5mm Allen

Key (x1)

2mm Allen

Key (x1)

Spacer

Bush (x4)

45mm/60mm

Bolts (x1 each)

Security

Washer (x1)

Head

Cap (x1)

Security

Screw (x1)

Bolt Through

Washers (x3)

M4 x 12mm (x4)

M4 x 16mm (x4)

M5 x 12mm (x4)

M5 x 16mm (x4)

Mounting

Head

Cover Plate

Base Plate

Display Mounting Screws (BAG B)

Hardware (BAG A)

Arm Assembly

(with pre-assembled Desk Clamp)

Tools Required:

Phillips Head Screwdriver

Power drill

8mm (

5

/16”) drill bit

IMPORTANT INFORMATION

! IMPORTANT - Install Levitate Single Monitor Arm as per Installation Instructions

! This product supports a maximum weight of 9kg (19.5lbs).

! This product supports VESA mounting hole configurations 75 x 75mm and 100 x 100mm.

! The manufacturer accepts no responsibility for incorrect installation.

Check you have received all parts against the Component Checklist and Hardware.

Step 1. Check Components

L-PB
L-PW

Desk | Single

Installation Instructions

Cable Covers

(x2 sets)

Insert

Brake Pin

PUSH

Desk Clamp

5mm Allen

Key

A2. Position Arm Assembly on the work

surface so that the Desk Clamp hangs over

the edge.

TOP LOADING ATTACHMENT

TIP: When sliding the Desk Clamp

between two work surfaces, ensure

that the Clamp Pad is fully open

and parallel with the edge of the

work surface.

Min. gap=18mm (0.71”)

Work Surface

(top view)

Desk

Clamp

A3. Using the 5mm Allen Key, close

the Desk Clamp to grip the work

surface. Tighten very firmly.

NOTE: The unique top loading Desk Clamp allows product installation/removal

without having to gain access to the underside of the work surface.

A4. Desk Clamp is now installed, please skip to Step 3 (PTO>>>).

The Clamp Pad will automatically

rotate under the work surface

when tightened.

Remove and re-install the Desk Clamp, using

the 5mm Allen Key supplied. Then go to A2.

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to the continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 22.07.11 ©

INSTALLATION COMPLETE - Refer to the User Operator Guide for user adjustments

How to remove the Monitor

Step 8. Monitor Orientation

TIGHTEN

VERY FIRMLY

(clockwise)

Clamp Pad

1. Rotate the monitor to Portrait or Landscape position

depending on user requirements.

NOTE: The monitor will only rotate 90° clockwise from

the starting position (when facing the screen).

2. Tilt the monitor up or down to suit the user.

TIP: Depending on the weight of the monitor, make

adjustments to the tilt tension using the 5mm Allen

Key if necessary.

5mm Allen

Key

MORE TENSION

(clockwise)

LESS TENSION

(anti-clockwise)

How to remove Cable Covers

1. If you inserted the Security Screw in Step 5, remove it

using a Phillips head screwdriver.

REMOVE

(anti-clockwise)

LIFT

Mounting Head

Quick Release

Coupling

1. Using a paper clip or a ball point pen press in

the three tabs holding the Cable Cover in place.

2. Pull the Cable Cover away from the Arm. Repeat this

process for each Cable Cover.

REMOVE

TIP: Access the tabs through the three

pinholes nearest the Cable Cover you

want to remove (e.g. A,B,C).

2. If you tightened the swivel tension in Step 5, loosen the

screw (do not remove) using the 2mm Allen Key supplied.

3. Unlock the Quick Release coupling (as shown below), and lift

the Monitor away from the Arm Assembly.

LESS TENSION

(anti-clockwise)

2mm Allen

Key

NOTE: When you press in the black inner button, the white outer

button will pop out to indicate the lock has been disengaged.

A
B
C

Upward/

Downward Tilt

Portrait/

Landscape

Rotation

Press in BLACK

inner button

TO UNLOCK

Petunjuk

Tampilkan panduan gratisAtdec L-PB di sini. Anda sudah membaca panduan tetapi tidak menjawab pertanyaan anda? Silakan ajukan pertanyaan anda pada halaman ini kepada pemilik Atdec L-PB lainnya. Ajukan pertanyaan Anda di sini

Apakah Anda memiliki pertanyaan tentang L-PB Atdec?

Apakah Anda memiliki pertanyaan tentang Atdec L-PB dan jawabannya tidak ada di manual? Ajukan pertanyaan Anda di sini. Berikan deskripsi yang jelas dan komprehensif tentang masalah dan pertanyaan Anda. Makin jelas masalah dan pertanyaan Anda, makin mudah bagi pemilik Atdec L-PB lainnya untuk menyediakan jawaban yang terbaik.

Jumlah pertanyaan: 0

spesifikasi produk

Di bawah ini, Anda akan menemukan spesifikasi produk dan spesifikasi manual dari Atdec L-PB.

Umum
Brand Atdec
Model L-PB
Produk Penyangga panel datar
EAN 881493006461, 8814930064610, 0881493006461
Bahasa Inggris
Jenis berkas Panduan pengguna (PDF)
Dudukan
Kompatibilitas ukuran layar minimal - "
Kompatibilitas ukuran layar maksimal 27 "
Jenis dudukan Meja tulis
Berat dan dimensi
Berat 4550 g
Fitur lainnya
Dimensi (PxLxT) 370 x 410 x 125 mm
Tampilkan lebih banyak

Pertanyaan yang Sering Ditanyakan

Tidak dapat menemukan jawaban atas pertanyaan Anda di manual? Anda dapat menemukan jawaban atas pertanyaan Anda di FAQ tentang Atdec L-PB di bawah ini.

Apakah pertanyaan Anda tidak terdaftar? Ajukan pertanyaan Anda di sini

Tidak ada hasil